無鉛控溫焊台-FX-888D無鉛焊台,比傳統HAKKO 936提高達30％

 FX-888D無鉛焊台特點：
焊鐵作業性能比傳統HAKKO 936提高達30％。
傳熱性能卓越，在相同作業條件下，比傳統焊台所需要之工作時間更快速。
可預設5個經常使用的溫度，只需按一下按鈕就可以把溫度鎖定。
只需2個按鈕，UP（選擇）和ENTER（決定），就可以全方位操作。
升溫時間比傳統焊台快20秒，作業時溫度下降幅度減少。
將焊鐵插入焊鐵架時所產生的聲音及振動減少達30％。
在同一焊鐵架可使用清潔海綿、焊咀清潔絲或清潔器清潔焊咀營成本。
焊鐵架底部可以拆除，容易清理錫渣。

 FX-888D無鉛焊台規格：
功 率 消 耗： 70W
輸 出 電 壓 ： AC 26V
發 熱 元 件 ： AC 26V，65W，陶瓷
控 溫 范 圍 ： 200～480℃
溫 度 穩 定： 土1℃（無負荷時）
焊 咀 與 接 地 阻 抗： 2Ω以下
焊 咀 與 接 地 電 位： 2mV以下
控 制 台 尺 寸： 120(W)X 93(H)X 170(D)mm
控 制 台 重 量： 約1.3kg
手 柄 重 量： 約44g
手 柄 長 度： 190mm
電 線 長 度： 1.2m
重量（不包括電線）：1.2Kg
總重量：2.4Kg

Heater output has been Increased by 30% compared to that
of the conventional models HAKKO 936937. Also FX-888D delivers excellent thermal recovery by using T18 series tips for

their terrific heat conductMty. This allows soldenng at a lower set temperature and reducing the thermal impact on components as well as tip oxidation that can shorten tip life.
　

Thermal recovery graph
Rise timc to 350^oC is 20 scconds tsstcr d tip tcmpcralijc drop is rcduccd durin9 continuous woili.

HAKKO FX-888D Performance. comparison graph with convntioi stations
Able to sho1en the time required to the swnc work and .improvc work efficiency significantly.

Test Criteria

Test Criteria

Measurement method: A thermocouple is mounted on the tip and the tip temperature is measured when soldering 1.6mmx5mm solder to paper phenol nnner hnrd nnr Pvrv rnnds

Measurement method: Thermocouples are mounted on the tip and the soldered portion on the board, and the time until the soldered portion reaches 250^oC is measured for 5 points.

Board: Paper phenol copper board

Board: Paper phenol copper board

Temperature setting: 350^oC

Component used: Connector

Solder: Lead-free solder (SnIAgfCu) Φl.6mmx5mm

Temperature setting: 360^oC

Solder: Lead-free solder (Sn/Ag/Cu) ΦO.5mm

Small footprint
Compact station body requires a space of only 100 (W) x 120 (D) mm. Whats more, points that come into contact with the floor are positioned as close to the outer edge of the body as possible to improve stability and make the station difficult to fall over.

Iron holder with full of functions
An iron holder of the same color of a soldering station comes as a set. The highly functional iron holder not only improves ease of use, but also brings a sense of visual consistency to the work environment.

Simple and easy operation
With only two operation buttons of UP and ENTER in the center, operation is simple and easy. Even if you’re not familiar with operation of machines, you can operate it without difficulty.